Table of Contents

Hall Effect

The Hall Effect occurs when an electrical charge passing through an electrical conductor produces an asymmetric distribution of charge resulting in a voltage difference and a magnetic field perpendicular to the current.

hallbook-8.jpg hallbook-9.jpg

The Hall Effect Sensor is a device that reacts to the magnetic field of a magnet and outputs a charge proportional to the distance of the magnet.

Very clear and thorough explanation by Professor Bowley of University of Nottingham:



To illustrate the way electrons behave as they travel through a conductor, let us look for a parallel example. The directional property of the flow of electrons though a conductor more closely resembles the flow of a hiker along a trail than water through a pipe. The trail is the path of least resistance, yet if subjected to an external force (say, for instance, the presence of a bear and cub) the hiker will veer to the opposite side of the trail. This is to say that the flow of electrons in a conductor may be directly influenced by forces outside of the conduit.

Closely linked to electric current is magnetism. Any electric current generates a magnetic field, and as was demonstrated by Michael Faraday, any magnetic field generates an electric current. In a conductor with an established current flow, the presence of a magnetic field will cause a deflection of current in which the potential of one transverse side of the conductor will have a higher potential than the other. This is what is known as the Hall Effect.

Shows the Hall effect for different directions of electric current and magnetic field.
1. Electrons (not conventional current!)
2. Hall element, or Hall sensor
3. Magnets
4. Magnetic field
5. Power source
In drawing "A", the Hall element takes on a negative charge at the top edge (symbolised by the blue color) and positive at the lower edge (red color). In "B" and "C", either the electric current or the magnetic field is reversed, causing the polarization to reverse. Reversing both current and magnetic field (drawing "D") causes the Hall element to again assume a negative charge at the upper edge.
From Wikipedia: Hall-effect

A simple hall effect sensor is comprised of two separate circuits:

In the absence of a magnetic field the measured voltage is insignificant, but when a magnetic field is applied either “into” or “out of” the semiconductor material, a voltage is induced across the width of the material. The hall voltage is directly proportional to the strength of the magnetic field. Note that the field strength, and thus the voltage, is not linearly related to the distance between the sensor and the source of the magnetic field (i.e. the magnet). The pole orientation of the magnet (either north or south polarity) with respect to the sensor, determines if the magnetic field lines are directed “into” or “out from” the sensor.

Types of hall effect sensors

Hall Effect sensors come in two basic types:

From Honeywell's Hallbook

From Honeywell's Hallbook


Hall sensors are commonly used to time the speed of wheels and shafts, such as for internal combustion engine ignition timing or tachometers. In the pictured wheel carrying two equally spaced magnets, the voltage from the sensor will peak twice for each revolution. This arrangement is commonly used to regulate the speed of diskette drives. It was also employed to measure speed of rotation in Elliot Sinyor's Gyrotyre, in a configuration similar to that shown below.

A wheel topped with two magnets that pass by a Hall effect sensor.  From Wikipedia: Hall_effect

Threshold devices can be used as proximity switches, or as counters. Several can be used together to do timing analysis or very coarse positional measurements.

Linear devices can measure field strength which varies with position (and thus speed and acceleration) though not linearly. Curve fitting techniques can be applied to give a linear relationship between output voltage and magnet distance. Linear devices and also be used as tilt sensors as the magnetic field strength varies with the projection in the transverse axis. Two or three-axis devices exist, allowing measurements to be done in more degrees of freedom.



An application for this sensor used in the context of musical instruments is the Hyper Flute by Cleo Palacio Quentin. There are two hall sensors used on the G# and C# levers of the flute. The small range of the keys are measured in ninety five steps giving the performer very precise control over the parameters she is controlling.

Explanation and performance by the artist on Interfaces Montreal (in French):


Honeywell SS49E


Description: Linear hall effect sensor
Datasheet: ss49e.series.chart.1.pdf

Melexis US1881EUA


Description: Threshold digital latch hall effect sensor
Datasheet: 0003715_hallapps.pdf

Everlight HI300/D1


Description: Threshold hall effect sensor
Datasheet: hall_effect.pdf



Hall Effect sensor Hall Effect Sensor

External links and references